Difference between revisions of "Fencing Draft:Weapons And Defensive Equipment"

From SCA Lochac
Jump to navigation Jump to search
 
(129 intermediate revisions by 4 users not shown)
Line 1: Line 1:
{{DISPLAYTITLE:Rules for equipment}}
+
<div class='rulesNumbering' style="counter-reset: page 9">
<div class='rulesNumbering' style="counter-reset: page 6">
 
==Protective material==
 
#There are four types of protective material. These are:
 
#*Rigid material
 
#*Penetration-resistant material
 
#*Abrasion-resistant material
 
#*Resilient padding.
 
#Rigid material is defined as a material that will not significantly flex, spread apart or deform under pressure of 12kg applied by a standard mask tester repeatedly to any single point. Example of rigid material that may comply with the standard are:
 
#*0.8mm stainless steel or 1mm mild steel
 
#*1.6mm aluminium, copper or brass
 
#*One layer of hardened heavy leather (225g/8oz; 4mm).
 
#Rigid material covering the face must be 12kg mesh (as found in a standard fencing mask) or perforated metal that meets the rigid protection standard. Perforated metal must have holes no larger than 3mm in diameter, with a minimum offset of 5mm.
 
#Penetration-resistant material is defined as any fabric or combination of fabrics that passes the Standard Fencing Armour Test in Appendix X. Commercial fencing clothing that is rated to at least 550 Newtons complies with this standard.
 
#Abrasion-resistant material is defined as fabric that will withstand normal combat stresses (such as being snagged by an unbroken blade), without tearing. Fabrics that do not comply with this standard include cotton gauze shirts and nylon pantyhose.
 
#Resilient padding is defined as any material or combination of materials—equivalent to 6mm of closed cell foam—that absorbs some of the force of a thrust or blow.
 
 
 
 
==Swords and daggers==
 
==Swords and daggers==
#The bladed weapons (swords and daggers) allowed for Fencing Combat in the Kingdom of Lochac are:
+
#The bladed weapons (swords and daggers) allowed for fencing combat in Lochac are:
##a sword, which has a blade length of between 45cm (18 inches) and 122cm (48 inches) and a grip no longer than 25cm (10 inches)
+
##a sword, which has a blade length of between 45 cm (18 inches) and 122 cm (48 inches) and a grip no longer than 25 cm (10 inches)
##a two-handed sword, which has a blade length of between 76cm (30 inches) and 122cm (48 inches) and a grip measuring between 25cm (10 inches) and 60cm (24 inches).
+
##a two-handed sword, which has a blade length of between 76 cm (30 inches) and 122 cm (48 inches) and a grip measuring between 25 cm (10 inches) and 60cm (24 inches). The combined blade and grip length for a two-handed sword must not exceed 152 cm (60 inches).
##The combined blade and grip length for a two-handed sword must not exceed 152cm (60 inches).
+
##a dagger, which has a blade length of between 30 cm (12 inches) and 45 cm (18 inches) and a grip no longer than 25 cm (10 inches).
##a dagger, which has a blade length of between 30cm (12 inches) and 45cm (18 inches) and a grip no longer than 25cm (10 inches).
+
#<span class="revision">Blades must have at most one substantial curve. Blades that are so curved that the tip does not contact the ground when the grip is perpendicular to the ground (i.e., pointed vertically) are not allowed (see Figure 3).</span>[[File:Curved_swords.png|thumb|300px| Figure 3. With the handle vertical, the tip must touch the ground. In this example, the sword on the left is allowed, the sword on the right is not.]]
#All swords and daggers must have a straight grip.
+
#All swords and daggers must have a substantially straight grip.
 +
#<span class="revision">Bladed weapons must not have more than one blade.
  
 
==Blades==
 
==Blades==
#Sword and dagger blades used in the Kingdom of Lochac can be made of steel or fibreglass.
+
Sword and dagger blades used in Lochac can be made of steel or fibreglass.
#Steel blades must be produced by a commercial entity and must meet the flexibility requirements in Appendix X.
+
===Steel blades===
##You are not allowed to use sword blades that are similar to a modern fencing foil, epee or sabre, including double-wide epees or ‘musketeer’ blades.  
+
#Steel blades must be produced by a commercial entity and must meet the flexibility requirements in [[Fencing:Safety_Tests |Safety tests]].
##You can use ‘Flexi daggers’ for standard Fencing. Flexi-daggers are not allowed in Cut and Thrust combat.
+
#You are not allowed to use sword blades that are similar to a modern fencing foil, epee or sabre, including double-wide epees or "musketeer" blades.  
##You must not use steel blades with kinks or cracks. Kinked or cracked blades cannot be repaired and must be retired.
+
#You can use "flexi-daggers" for Standard fencing. Flexi-daggers are not allowed in Cut and Thrust combat.
##You must not use a blade with a sharp bend or an ‘S’ curve. You can try to re-curve the blade, but a marshal must inspect the blade and agree that it can be used again.
+
#You must not use steel blades with kinks or cracks. Kinked or cracked blades cannot be repaired and must be retired.
 +
#You must not use a blade with a sharp bend or an "S" curve. You can try to re-curve the blade, but a marshal must inspect the blade and agree that it can be used again.
 
#You must not do anything that might change the temper of the blade or affect its flexibility. This includes grinding, cutting, heating or hammering the blade. Normal combat stresses and blade care do not violate this rule. Exceptions to the rule are:
 
#You must not do anything that might change the temper of the blade or affect its flexibility. This includes grinding, cutting, heating or hammering the blade. Normal combat stresses and blade care do not violate this rule. Exceptions to the rule are:
##you can change the length or width of the tang
+
##You can change the length or width of the tang.
##you can shorten a blade, as long as it still meets the flexibility requirements
+
##You can shorten a blade, as long as it still meets the flexibility requirements.
##you can file the end of the tip to make it blunt
+
##You can file the end of the tip to make it blunt.
##you can weld a nut or another blunt metal object to the tip to spread impact, as long as you take care to avoid changing the temper of the blade.
+
##You can weld a nut or another blunt metal object to the tip to spread impact, as long as you take care to avoid changing the temper of the blade.
#Fibreglass blades must meet the flexibility requirements in Appendix X
+
 
 +
===Fibreglass blades===
 +
#<span class="revision">Lochac has a Society level exemption allowing fibreglass blades.
 +
#Fibreglass blades must meet the flexibility requirements in [[Fencing:Safety_Tests |Safety tests]].
 
#Fibreglass blades must be made only using fibreglass rod, glue and fibreglass and vinyl tapes. You can use metal to mount the hilt, but it must extend no longer than 10cm along the blade.
 
#Fibreglass blades must be made only using fibreglass rod, glue and fibreglass and vinyl tapes. You can use metal to mount the hilt, but it must extend no longer than 10cm along the blade.
##The blade must be wrapped in vinyl duct tape (not cloth or metal-backed). If you use fibreglass strapping tape to make the blade, this must be completely covered by the outer wrapping tape.
+
#The blade must be wrapped in vinyl duct tape (not cloth or metal-backed). If you use fibreglass strapping tape to make the blade, this must be completely covered by the outer wrapping tape.
  
 
==Tips==
 
==Tips==
 
#The tip of a blade must be blunt, with no sharp edges or corners.
 
#The tip of a blade must be blunt, with no sharp edges or corners.
#You must cover the tip with a ‘blunt’:
+
#You must cover the tip with a "blunt".
##the blunt can be made of shatter-resistant polymer, rubber or leather
+
##The blunt can be made of shatter-resistant polymer, rubber or leather.
##it must have a minimum size of 10mm on any surface that strikes the opponent.
+
##<span class="revision">The blunt must have a minimum size of 10 mm on any surface that strikes the opponent.
##polymer and rubber blunts must be at least 3mm thick between the striking surface and the tip or edge of the blade. Leather blunts must be at least 1.6mm thick.
+
##Polymer and rubber blunts must be at least 3mm thick between the striking surface and the tip or edge of the blade. Leather blunts must be at least 1.6 mm thick.
##you must replace the blunt if it looks like it is bulging or cracking, if there are signs the tip of the blade is breaking, or, in the case of a polymer blunt, if the plastic is changing colour.
+
#You must replace the blunt if it looks like it is bulging or cracking, if there are signs the tip of the blade is breaking, or, in the case of a polymer blunt, if the plastic is changing colour.
##your blunt must be a different colour to the blade, so that you can tell if the blunt is missing.
+
#<span class="revision">Your blunt must be a different colour to the blade and any tape used, so that you can tell if the blunt is missing.
 
#You must tape or glue the blunt to the blade, so that it will not fly off under reasonable combat conditions.
 
#You must tape or glue the blunt to the blade, so that it will not fly off under reasonable combat conditions.
##your blunt must be a different colour to the blade, so that you can tell if the blunt is missing
+
##<span class="revision">Blunts which are glued to the blade must still be taped, so that you can tell if necessary tape is missing.
##you must make sure the tape does not cover the front of the blunt, so that you can tell if the tip of the blade is breaking through.
+
#<span class="revision>The tape must not cover the front of the blunt, so that you can tell if the tip of the blade is breaking through.
  
 
==Other sword parts==
 
==Other sword parts==
 
#Sword and dagger hilts, handles, pommels and other parts not meant to strike the opponent can be made of metal, wood, leather or a reasonable facsimile.
 
#Sword and dagger hilts, handles, pommels and other parts not meant to strike the opponent can be made of metal, wood, leather or a reasonable facsimile.
 +
#The ends of quillons and pommels must be blunt.
  
 
==Spears==
 
==Spears==
#There are two types of spears allowed in Fencing Combat.
+
#<span class="revision">You can use rubber-headed spears for fencing combat in Lochac. You cannot use steel-headed spears.
#*Rubber-headed spear
 
#*Steel-headed spear.
 
 
 
===Rubber-headed spear===
 
 
#Rubber-headed spears must be made of a flexible rubber head mounted on a rattan haft.
 
#Rubber-headed spears must be made of a flexible rubber head mounted on a rattan haft.
#The spear-head must be purchased from a commercial vendor as a spear tip or spike with a head length of between 10cm (4 inches) and 51cm (20 inches). The rubber at the tip must be at least 6mm (1/4 inch) thick.
+
#The spear-head must be purchased from a commercial vendor as a spear tip or spike with a head length of between 10 cm (4 inches) and 51 cm (20 inches). The rubber at the tip must be at least 6 mm (1/4 inch) thick.
 
##The flexible tip must extend at least 10cm past the end of the haft.
 
##The flexible tip must extend at least 10cm past the end of the haft.
 
##The spear-head must flex to 90 degrees with hand pressure and must substantially return to its shape within 3 seconds
 
##The spear-head must flex to 90 degrees with hand pressure and must substantially return to its shape within 3 seconds
#The rattan haft must have a diameter between 28.5mm (1 1/8th inch) and 35mm (1 3/8th inch):
+
#The rattan haft must have a diameter between 28.5 mm (1 1/8th inch) and 35 mm (1 3/8th inch):
##The haft must be inserted at least 5cm (2”) into the spear-head. The head must be friction-fitted to the haft according to the manufacturer’s instructions.  
+
##The haft must be inserted at least 5cm (2 inches) into the spear-head. The head must be friction-fitted to the haft according to the manufacturer's instructions.  
##The head must be taped to the haft with strapping tape, fibreglass tape or duct tape. Contrasting coloured tape must be wrapped around the base of the head, so that the head’s absence is readily apparent.
+
##The head must be taped to the haft with strapping tape, fibreglass tape or duct tape. Contrasting coloured tape must be wrapped around the base of the head, so that the head's absence is readily apparent.
##The haft must have a flat end at the head of the spear with a diameter of at least 12mm (1/2”). The butt end of the haft may be rounded.
+
##The haft must have a flat end at the head of the spear with a diameter of at least 12 mm (1/2 inch). The butt end of the haft may be rounded.
#You can put tape on the haft to help prolong its life. You can add augmentations or decorations, for example to stop a blade sliding along the haft or to make the haft easier to grip. You must make sure those augmentations do not weaken the haft or pose a safety risk. You cannot use augmentations that are designed to trap a blade
+
#You can put tape on the haft to help prolong its life.
#The total length of the spear must be no longer than 275cm (9 feet).
+
#You can add augmentations or decorations, for example to stop a blade sliding along the haft or to make the haft easier to grip, but they must not weaken the haft or pose a safety risk. You cannot use augmentations that are designed to trap a blade.
 +
#The total length of the spear must be no longer than 275 cm (9 feet).
 +
#<span class="revision">Spears may have a spear-head at each end.
 +
 
 +
==Rubber band guns==
 +
===Guns===
 +
#Rubber band guns must look like a period muzzle-loading weapon dated before 1600CE.
 +
#Rubber band guns must be made of sturdy, lightweight materials that will stand up to normal combat. You must make sure all edges and corners are smoothed off and that there are no splinters or cracks.
 +
#There are two categories of rubber band guns, classified by draw length - the distance between the nock and the seer attached to the trigger that the ammunition hooks onto:
 +
##Short-arm rubber band guns have a draw length not exceeding 45cm.
 +
##Long-arm rubber band guns have a draw length exceeding 45cm.
 +
[[File:Draw_length_of_RBG.png|thumb|600px|Figure 4. Draw length of a rubber band gun]]
  
===Steel-headed spear===
+
===Ammunition===
#Steel-headed spears must be made of a metal blade head mounted on a wooden or rattan haft.
 
##The metal head must be similar in design to the commercially available Alchem pike and Amazonia spear.
 
##The head must be at least 91.4cm (36”) long, as measured from the tip to the top of the tang. It must comply with the flexibility requirements for competitive swordfighting in Appendix X.
 
##The head must be secured to the haft by screws or pins.
 
#You can add augmentations to the haft (see rule 6.6.5)
 
#The total length of the spear must be no longer than 244cm (8 feet).
 
#The maximum weight of the weapon must not be more than 1.36kg (3lbs).
 
'''Note: Steel-headed spears will not be permitted for Fencing Combat after 31 December 2020, at the direction of the Society Marshal.
 
  
==Rubber-band guns==
+
#Rubber band ammunition must be made from commercially available rubber tubing and must not contain any metal parts.
#Rubber-band guns (RBGs) must look like a period muzzle-loading weapon dated before 1600CE.
+
#Ammunition must not use any rigid materials beyond the minimum required to join the ends together. Any hard plastic on the outside of the band should be covered and smoothed by vinyl duct tape or plastic shrink wrapping.  
#RBGS must be made of sturdy, lightweight materials that will stand up to normal combat. You must make sure all edges and corners are smoothed off and that there are no splinters or cracks.
+
#You are not allowed to fill the rubber bands with sand or liquids.  
#Rubber band ammunition must be made from commercially available rubber tubing and must not contain any metal parts:
+
#You must mark each band to identify the owner.
#*Ammunition must not use any rigid materials beyond the minimum required to join the ends together. Any hard plastic on the outside of the band should be covered and smoothed by vinyl duct tape or plastic shrink wrapping.  
+
#You can only use ammunition that has been inspected with the weapon you are using. You are not allowed to collect used ammunition during combat.
#*You are not allowed to fill the rubber bands with sand or liquids.  
+
#Ammunition must have a draw strength no greater than 13.6 kg (30 pounds). Ammunition must be tested when new and regularly to ensure it complies with this rule.
#*You must mark each band to identify the owner.
+
#The circumference of the ammunition depends on the category of rubber band gun.
#*You can only use ammunition that has been inspected with the weapon you are using. You are not allowed to collect used ammunition during combat.
+
#There is no restriction on the circumference of short-arm rubber band gun ammunition
#There are two categories of RBG, classified by draw length—the distance between the anchor point and the trigger that the ammunition hooks onto (as shown in Figure X):
+
#The circumference of long-arm rubber band gun ammunition must be at least the draw length of the rubber band gun.  
#*Short-arm RBGs have a draw length not exceeding 45cm
+
##For example, if an rubber band gun has a draw length of 46cm, then the ammunition must have a circumference of at least 46cm.  
#*Long-arm RBGs have a draw length exceeding 45cm
+
##As a practical measure, a marshal can flatten a band in half, and use that to measure it against the draw length of the rubber band gun.
#The circumference of the ammunition (as shown in Figure X) depends on the category of RBG.  
+
#<span class="revision">Rubber tubing used to make ammunition must have a minimum diameter of 6 mm while at rest.
#*There is no restriction on the circumference of short-arm RBG ammunition
 
#*The circumference of long-arm RBG ammunition must be the same or greater than the draw length of the RBG.  
 
#*For example, if an RBG has a draw length of 46cm, then the ammunition must have a circumference of at least 46 cm.  
 
#*As a practical measure, a marshal can flatten a band in half, and use that to measure it against the draw length of the RBG (as shown in '''Figure X''').
 
  
 
==Defensive objects==
 
==Defensive objects==
#There are two types of defensive object: Rigid; and non-rigid.
+
===General===
 +
#There are two types of defensive object:
 +
#*rigid
 +
#*non-rigid.
 
#Rigid defensive objects must be made of sturdy materials that will stand up to the stresses of normal combat. You must make sure that all edges or corners are smoothed and that there are no cracks or splinters.
 
#Rigid defensive objects must be made of sturdy materials that will stand up to the stresses of normal combat. You must make sure that all edges or corners are smoothed and that there are no cracks or splinters.
 
#Non-rigid objects may be made of cloth, leather and similar yielding materials. They may be weighted with soft material such as rope or rolled cloth. They may not be weighted with any rigid material, nor with materials that are heavy enough to turn the object into a flail or impact weapon.
 
#Non-rigid objects may be made of cloth, leather and similar yielding materials. They may be weighted with soft material such as rope or rolled cloth. They may not be weighted with any rigid material, nor with materials that are heavy enough to turn the object into a flail or impact weapon.
 
#Defensive objects that contain both rigid and non-rigid components (such as a flag on a pole) must meet both sets of requirements. You cannot throw these objects (including, for example, a cloak with rigid clasps) at your opponent.
 
#Defensive objects that contain both rigid and non-rigid components (such as a flag on a pole) must meet both sets of requirements. You cannot throw these objects (including, for example, a cloak with rigid clasps) at your opponent.
#You are not allowed to use an object that can bind an opponent’s weapon to their body, or to their other weapon or defensive object—either deliberately or by accident. This might include ropes or whips. You can use a coiled rope or whip to deflect a weapon.
+
#<span class="revision">Objects which even temporarily entangle their opponent's weapon to their person or equipment, whether by design or repeated mishap, are not allowed. This may include ropes or whips used in this manner. Ropes or whips used in such a way as to deflect and not entangle a fencer are allowed.
 +
 
 +
===Non-standard defensive equipment===
 +
#Non-standard equipment must be approved by the Fencing Marshal-in-Charge.
 +
#You can put a simulated spike or a similar offensive item on your buckler or shield.
 +
##Offensive items must only be made of cloth, foam, leather, glue and tape and must not contain rigid materials.
 +
##On inspection, the offensive item must provide progressively resistant "give", without allowing contact with any underlying material.
 +
#You must tell your opponent if you are using non-standard equipment. They can decide not to face it and ask you to use something else.
 +
#<span class="revision">Non-standard defensive equipment includes, but is not limited to:
 +
#*<span class="revision">bucklers with a spike or projection more than two inches perpendicular to the main plane of the buckler or the central boss, whichever is applicable. The central boss does not count as a spike or projection.
 +
#*<span class="revision">bucklers with additions which could reasonably be expected to trap or catch a blade (such as rings or hooks);
 +
#*<span class="revision">axes;
 +
#*<span class="revision">Talhoffer "judicial duelling shields" and Talhoffer bucklers; and
 +
#*<span class="revision">bucklers made out of uncommon materials, such as vegetables, children's toys, etc.
 +
#:<span class="revision">Fencers and marshals should use common sense when applying this definition and be conservative when considering if a defensive item is non-standard, especially when a less-experienced fighter is concerned if an object would be safe to fence against.
 +
 
  
===Non-standard defensive objects===
 
#You can put a simulated spike or a similar offensive item on your buckler or shield. This is non-standard equipment and must be approved by the Fencing Marshal in Charge.
 
#*Offensive items must only be made of cloth, foam, leather, glue and tape and must not contain rigid materials.
 
#*On inspection, the offensive item must provide progressively resistant ‘give’, without allowing contact with any underlying material.
 
#You must tell your opponent if you are using non-standard equipment. They can decline to face it without forfeiting the bout.
 
 
</div>
 
</div>
[[Category:Draft Rapier Handbook | f]]
+
[[Category:Fencing Draft Handbook | I]]
 +
[[Category:Fencing Draft Handbook Logged | I]]

Latest revision as of 21:29, 27 October 2023

Swords and daggers

  1. The bladed weapons (swords and daggers) allowed for fencing combat in Lochac are:
    1. a sword, which has a blade length of between 45 cm (18 inches) and 122 cm (48 inches) and a grip no longer than 25 cm (10 inches)
    2. a two-handed sword, which has a blade length of between 76 cm (30 inches) and 122 cm (48 inches) and a grip measuring between 25 cm (10 inches) and 60cm (24 inches). The combined blade and grip length for a two-handed sword must not exceed 152 cm (60 inches).
    3. a dagger, which has a blade length of between 30 cm (12 inches) and 45 cm (18 inches) and a grip no longer than 25 cm (10 inches).
  2. Blades must have at most one substantial curve. Blades that are so curved that the tip does not contact the ground when the grip is perpendicular to the ground (i.e., pointed vertically) are not allowed (see Figure 3).
    Figure 3. With the handle vertical, the tip must touch the ground. In this example, the sword on the left is allowed, the sword on the right is not.
  3. All swords and daggers must have a substantially straight grip.
  4. Bladed weapons must not have more than one blade.

Blades

Sword and dagger blades used in Lochac can be made of steel or fibreglass.

Steel blades

  1. Steel blades must be produced by a commercial entity and must meet the flexibility requirements in Safety tests.
  2. You are not allowed to use sword blades that are similar to a modern fencing foil, epee or sabre, including double-wide epees or "musketeer" blades.
  3. You can use "flexi-daggers" for Standard fencing. Flexi-daggers are not allowed in Cut and Thrust combat.
  4. You must not use steel blades with kinks or cracks. Kinked or cracked blades cannot be repaired and must be retired.
  5. You must not use a blade with a sharp bend or an "S" curve. You can try to re-curve the blade, but a marshal must inspect the blade and agree that it can be used again.
  6. You must not do anything that might change the temper of the blade or affect its flexibility. This includes grinding, cutting, heating or hammering the blade. Normal combat stresses and blade care do not violate this rule. Exceptions to the rule are:
    1. You can change the length or width of the tang.
    2. You can shorten a blade, as long as it still meets the flexibility requirements.
    3. You can file the end of the tip to make it blunt.
    4. You can weld a nut or another blunt metal object to the tip to spread impact, as long as you take care to avoid changing the temper of the blade.

Fibreglass blades

  1. Lochac has a Society level exemption allowing fibreglass blades.
  2. Fibreglass blades must meet the flexibility requirements in Safety tests.
  3. Fibreglass blades must be made only using fibreglass rod, glue and fibreglass and vinyl tapes. You can use metal to mount the hilt, but it must extend no longer than 10cm along the blade.
  4. The blade must be wrapped in vinyl duct tape (not cloth or metal-backed). If you use fibreglass strapping tape to make the blade, this must be completely covered by the outer wrapping tape.

Tips

  1. The tip of a blade must be blunt, with no sharp edges or corners.
  2. You must cover the tip with a "blunt".
    1. The blunt can be made of shatter-resistant polymer, rubber or leather.
    2. The blunt must have a minimum size of 10 mm on any surface that strikes the opponent.
    3. Polymer and rubber blunts must be at least 3mm thick between the striking surface and the tip or edge of the blade. Leather blunts must be at least 1.6 mm thick.
  3. You must replace the blunt if it looks like it is bulging or cracking, if there are signs the tip of the blade is breaking, or, in the case of a polymer blunt, if the plastic is changing colour.
  4. Your blunt must be a different colour to the blade and any tape used, so that you can tell if the blunt is missing.
  5. You must tape or glue the blunt to the blade, so that it will not fly off under reasonable combat conditions.
    1. Blunts which are glued to the blade must still be taped, so that you can tell if necessary tape is missing.
  6. The tape must not cover the front of the blunt, so that you can tell if the tip of the blade is breaking through.

Other sword parts

  1. Sword and dagger hilts, handles, pommels and other parts not meant to strike the opponent can be made of metal, wood, leather or a reasonable facsimile.
  2. The ends of quillons and pommels must be blunt.

Spears

  1. You can use rubber-headed spears for fencing combat in Lochac. You cannot use steel-headed spears.
  2. Rubber-headed spears must be made of a flexible rubber head mounted on a rattan haft.
  3. The spear-head must be purchased from a commercial vendor as a spear tip or spike with a head length of between 10 cm (4 inches) and 51 cm (20 inches). The rubber at the tip must be at least 6 mm (1/4 inch) thick.
    1. The flexible tip must extend at least 10cm past the end of the haft.
    2. The spear-head must flex to 90 degrees with hand pressure and must substantially return to its shape within 3 seconds
  4. The rattan haft must have a diameter between 28.5 mm (1 1/8th inch) and 35 mm (1 3/8th inch):
    1. The haft must be inserted at least 5cm (2 inches) into the spear-head. The head must be friction-fitted to the haft according to the manufacturer's instructions.
    2. The head must be taped to the haft with strapping tape, fibreglass tape or duct tape. Contrasting coloured tape must be wrapped around the base of the head, so that the head's absence is readily apparent.
    3. The haft must have a flat end at the head of the spear with a diameter of at least 12 mm (1/2 inch). The butt end of the haft may be rounded.
  5. You can put tape on the haft to help prolong its life.
  6. You can add augmentations or decorations, for example to stop a blade sliding along the haft or to make the haft easier to grip, but they must not weaken the haft or pose a safety risk. You cannot use augmentations that are designed to trap a blade.
  7. The total length of the spear must be no longer than 275 cm (9 feet).
  8. Spears may have a spear-head at each end.

Rubber band guns

Guns

  1. Rubber band guns must look like a period muzzle-loading weapon dated before 1600CE.
  2. Rubber band guns must be made of sturdy, lightweight materials that will stand up to normal combat. You must make sure all edges and corners are smoothed off and that there are no splinters or cracks.
  3. There are two categories of rubber band guns, classified by draw length - the distance between the nock and the seer attached to the trigger that the ammunition hooks onto:
    1. Short-arm rubber band guns have a draw length not exceeding 45cm.
    2. Long-arm rubber band guns have a draw length exceeding 45cm.
Figure 4. Draw length of a rubber band gun

Ammunition

  1. Rubber band ammunition must be made from commercially available rubber tubing and must not contain any metal parts.
  2. Ammunition must not use any rigid materials beyond the minimum required to join the ends together. Any hard plastic on the outside of the band should be covered and smoothed by vinyl duct tape or plastic shrink wrapping.
  3. You are not allowed to fill the rubber bands with sand or liquids.
  4. You must mark each band to identify the owner.
  5. You can only use ammunition that has been inspected with the weapon you are using. You are not allowed to collect used ammunition during combat.
  6. Ammunition must have a draw strength no greater than 13.6 kg (30 pounds). Ammunition must be tested when new and regularly to ensure it complies with this rule.
  7. The circumference of the ammunition depends on the category of rubber band gun.
  8. There is no restriction on the circumference of short-arm rubber band gun ammunition
  9. The circumference of long-arm rubber band gun ammunition must be at least the draw length of the rubber band gun.
    1. For example, if an rubber band gun has a draw length of 46cm, then the ammunition must have a circumference of at least 46cm.
    2. As a practical measure, a marshal can flatten a band in half, and use that to measure it against the draw length of the rubber band gun.
  10. Rubber tubing used to make ammunition must have a minimum diameter of 6 mm while at rest.

Defensive objects

General

  1. There are two types of defensive object:
    • rigid
    • non-rigid.
  2. Rigid defensive objects must be made of sturdy materials that will stand up to the stresses of normal combat. You must make sure that all edges or corners are smoothed and that there are no cracks or splinters.
  3. Non-rigid objects may be made of cloth, leather and similar yielding materials. They may be weighted with soft material such as rope or rolled cloth. They may not be weighted with any rigid material, nor with materials that are heavy enough to turn the object into a flail or impact weapon.
  4. Defensive objects that contain both rigid and non-rigid components (such as a flag on a pole) must meet both sets of requirements. You cannot throw these objects (including, for example, a cloak with rigid clasps) at your opponent.
  5. Objects which even temporarily entangle their opponent's weapon to their person or equipment, whether by design or repeated mishap, are not allowed. This may include ropes or whips used in this manner. Ropes or whips used in such a way as to deflect and not entangle a fencer are allowed.

Non-standard defensive equipment

  1. Non-standard equipment must be approved by the Fencing Marshal-in-Charge.
  2. You can put a simulated spike or a similar offensive item on your buckler or shield.
    1. Offensive items must only be made of cloth, foam, leather, glue and tape and must not contain rigid materials.
    2. On inspection, the offensive item must provide progressively resistant "give", without allowing contact with any underlying material.
  3. You must tell your opponent if you are using non-standard equipment. They can decide not to face it and ask you to use something else.
  4. Non-standard defensive equipment includes, but is not limited to:
    • bucklers with a spike or projection more than two inches perpendicular to the main plane of the buckler or the central boss, whichever is applicable. The central boss does not count as a spike or projection.
    • bucklers with additions which could reasonably be expected to trap or catch a blade (such as rings or hooks);
    • axes;
    • Talhoffer "judicial duelling shields" and Talhoffer bucklers; and
    • bucklers made out of uncommon materials, such as vegetables, children's toys, etc.
    Fencers and marshals should use common sense when applying this definition and be conservative when considering if a defensive item is non-standard, especially when a less-experienced fighter is concerned if an object would be safe to fence against.