Armoured Combat:Throwing Weapon Standards: Difference between revisions
Jump to navigation
Jump to search
(3.0.1) |
(Changed for v3.4) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
==General Information== | ==General Information== | ||
# | #You can use throwing weapons in scenarios where thrown weapons are allowed. | ||
#Weapons used | #Some throwing weapons may also be used for striking. Examples include thrust-and-throw javelins, axes, and knives. | ||
#Weapons held in the hand, and used for striking as well as throwing must be constructed according to the requirements for that style of melee weapon as well as the requirements set out in this section. | |||
#The total mass of throwing weapons may not exceed 907g (2 lb). | #The total mass of throwing weapons may not exceed 907g (2 lb). | ||
#Shafts | #Shafts must be constructed of either: | ||
##rattan not less than 32mm (1 1/4 inch) in diameter along its entire length; or | ##rattan not less than 32mm (1 1/4 inch) in diameter along its entire length; or | ||
##two layers of Siloflex or equivalent. The approved equivalent for Lochac is medium density, black polyethylene water pipe, 12 bar pressure rating. The outer layer | ##two layers of Siloflex or equivalent. The approved equivalent for Lochac is medium density, black polyethylene water pipe, 12 bar pressure rating. The outer layer must be 25.4mm (1 inch) inner diameter Siloflex (32mm (1 1/4 inch) OD) and the inner layer must be 19.1mm (3/4 inch) inner diameter Siloflex. | ||
#If Siloflex is used, both ends of the shaft | #If Siloflex is used, both ends of the shaft must be covered with either a schedule-40 PVC cap with an interior diameter the same as the outside diameter of the shaft (32mm (1 1/4 inch)), or with a rubber stopper or equivalent means to prevent the tubing from penetrating the thrusting tip(s), fastened securely in place by tape and/or glue. | ||
#Low-profile thrusting tips, built according to the specifications in [[Armoured Combat:Melee_Weapon_Standards#Low-profile_Thrusting_Tips|8.4.2]] | #Low-profile thrusting tips, built according to the specifications in [[Armoured Combat:Melee_Weapon_Standards#Low-profile_Thrusting_Tips|8.4.2]] must be used on any tip that can be reasonably assumed to contact a fighter when the weapon is used or thrown. | ||
#Throwing weapons with a thrusting tip on only one end | #Throwing weapons with a thrusting tip on only one end must be constructed so that when you throw them, they will always strike with that tip. If necessary, fins, fletchings, streamers, etc. must be used to prevent the weapon from turning and striking with any other tip. The fins must be constructed of a non-rigid material, such as closed-cell foam or un-hardened leather. | ||
#If the weapon has a head, it | #If the weapon has a head, it must not be constructed solely of rigid materials. The head must be firmly and securely attached to the haft or handle. The head must allow at least 13mm of progressive give between the striking surface and the weapon haft or handle. | ||
#Throwing weapons must have the owner's name, kingdom, and group clearly and legibly printed on it in English characters for identification. | #Throwing weapons must have the owner's name, kingdom, and group clearly and legibly printed on it in English characters for identification. | ||
</div> | </div> | ||
[[Category:Fighters Handbook | I]] | [[Category:Fighters Handbook | I]] | ||
Latest revision as of 07:41, 25 July 2024
General Information
- You can use throwing weapons in scenarios where thrown weapons are allowed.
- Some throwing weapons may also be used for striking. Examples include thrust-and-throw javelins, axes, and knives.
- Weapons held in the hand, and used for striking as well as throwing must be constructed according to the requirements for that style of melee weapon as well as the requirements set out in this section.
- The total mass of throwing weapons may not exceed 907g (2 lb).
- Shafts must be constructed of either:
- rattan not less than 32mm (1 1/4 inch) in diameter along its entire length; or
- two layers of Siloflex or equivalent. The approved equivalent for Lochac is medium density, black polyethylene water pipe, 12 bar pressure rating. The outer layer must be 25.4mm (1 inch) inner diameter Siloflex (32mm (1 1/4 inch) OD) and the inner layer must be 19.1mm (3/4 inch) inner diameter Siloflex.
- If Siloflex is used, both ends of the shaft must be covered with either a schedule-40 PVC cap with an interior diameter the same as the outside diameter of the shaft (32mm (1 1/4 inch)), or with a rubber stopper or equivalent means to prevent the tubing from penetrating the thrusting tip(s), fastened securely in place by tape and/or glue.
- Low-profile thrusting tips, built according to the specifications in 8.4.2 must be used on any tip that can be reasonably assumed to contact a fighter when the weapon is used or thrown.
- Throwing weapons with a thrusting tip on only one end must be constructed so that when you throw them, they will always strike with that tip. If necessary, fins, fletchings, streamers, etc. must be used to prevent the weapon from turning and striking with any other tip. The fins must be constructed of a non-rigid material, such as closed-cell foam or un-hardened leather.
- If the weapon has a head, it must not be constructed solely of rigid materials. The head must be firmly and securely attached to the haft or handle. The head must allow at least 13mm of progressive give between the striking surface and the weapon haft or handle.
- Throwing weapons must have the owner's name, kingdom, and group clearly and legibly printed on it in English characters for identification.