Rules for equipment

From SCA Lochac
Revision as of 07:55, 5 January 2021 by Angele (talk | contribs) (→‎Blades)
Jump to navigation Jump to search

Protective material

  1. There are four types of protective material. These are:
    • Rigid material
    • Penetration-resistant material
    • Abrasion-resistant material
    • Resilient padding.
  2. Rigid material is defined as a material that will not significantly flex, spread apart or deform under pressure of 12kg applied by a standard mask tester repeatedly to any single point. Example of rigid material that may comply with the standard are:
    • 0.8mm stainless steel or 1mm mild steel
    • 1.6mm aluminium, copper or brass
    • One layer of hardened heavy leather (225g/8oz; 4mm).
  3. Rigid material covering the face must be 12kg mesh (as found in a standard fencing mask) or perforated metal that meets the rigid protection standard. Perforated metal must have holes no larger than 3mm in diameter, with a minimum offset of 5mm.
  4. Penetration-resistant material is defined as any fabric or combination of fabrics that passes the Standard Fencing Armour Test in Chapter 7 - Safety tests. Commercial fencing clothing that is rated to at least 550 Newtons complies with this standard.
  5. Abrasion-resistant material is defined as fabric that will withstand normal combat stresses (such as being snagged by an unbroken blade), without tearing. Fabrics that do not comply with this standard include cotton gauze shirts and nylon pantyhose.
  6. Resilient padding is defined as any material or combination of materials - equivalent to 6mm of closed cell foam - that absorbs some of the force of a thrust or blow.

Swords and daggers

  1. The bladed weapons (swords and daggers) allowed for fencing combat in Lochac are:
    1. a sword, which has a blade length of between 45 cm (18 inches) and 122 cm (48 inches) and a grip no longer than 25 cm (10 inches)
    2. a two-handed sword, which has a blade length of between 76 cm (30 inches) and 122 cm (48 inches) and a grip measuring between 25 cm (10 inches) and 60cm (24 inches).
    3. The combined blade and grip length for a two-handed sword must not exceed 152 cm (60 inches).
    4. a dagger, which has a blade length of between 30 cm (12 inches) and 45 cm (18 inches) and a grip no longer than 25 cm (10 inches).
  2. All swords and daggers must have a substantially straight grip.

Blades

  1. Sword and dagger blades used in Lochac can be made of steel or fibreglass.
  2. Steel blades must be produced by a commercial entity and must meet the flexibility requirements in Chapter 7 - Safety tests.
    1. You are not allowed to use sword blades that are similar to a modern fencing foil, epee or sabre, including double-wide epees or "musketeer" blades.
    2. You can use "flexi-daggers" for Standard fencing. Flexi-daggers are not allowed in Cut and Thrust combat.
    3. You must not use steel blades with kinks or cracks. Kinked or cracked blades cannot be repaired and must be retired.
    4. You must not use a blade with a sharp bend or an "S" curve. You can try to re-curve the blade, but a marshal must inspect the blade and agree that it can be used again.
  3. You must not do anything that might change the temper of the blade or affect its flexibility. This includes grinding, cutting, heating or hammering the blade. Normal combat stresses and blade care do not violate this rule. Exceptions to the rule are:
    1. You can change the length or width of the tang.
    2. You can shorten a blade, as long as it still meets the flexibility requirements.
    3. You can file the end of the tip to make it blunt.
    4. You can weld a nut or another blunt metal object to the tip to spread impact, as long as you take care to avoid changing the temper of the blade.
  4. Fibreglass blades must meet the flexibility requirements in Chapter 7 - Safety tests.
  5. Fibreglass blades must be made only using fibreglass rod, glue and fibreglass and vinyl tapes. You can use metal to mount the hilt, but it must extend no longer than 10cm along the blade.
    1. The blade must be wrapped in vinyl duct tape (not cloth or metal-backed). If you use fibreglass strapping tape to make the blade, this must be completely covered by the outer wrapping tape.

Tips

  1. The tip of a blade must be blunt, with no sharp edges or corners.
  2. You must cover the tip with a "blunt".
    1. The blunt can be made of shatter-resistant polymer, rubber or leather.
    2. The blunt must have a minimum size of 10mm on any surface that strikes the opponent.
    3. Polymer and rubber blunts must be at least 3mm thick between the striking surface and the tip or edge of the blade. Leather blunts must be at least 1.6mm thick.
  3. You must replace the blunt if it looks like it is bulging or cracking, if there are signs the tip of the blade is breaking, or, in the case of a polymer blunt, if the plastic is changing colour.
  4. Your blunt must be a different colour to the blade, so that you can tell if the blunt is missing.
  5. You must tape or glue the blunt to the blade, so that it will not fly off under reasonable combat conditions.
  6. You must make sure the tape does not cover the front of the blunt, so that you can tell if the tip of the blade is breaking through.

Other sword parts

Sword and dagger hilts, handles, pommels and other parts not meant to strike the opponent can be made of metal, wood, leather or a reasonable facsimile.

Spears

General

There are two types of spears allowed in fencing combat.

  • Rubber-headed spear
  • Steel-headed spear.

Rubber-headed spear

  1. Rubber-headed spears must be made of a flexible rubber head mounted on a rattan haft.
  2. The spear-head must be purchased from a commercial vendor as a spear tip or spike with a head length of between 10cm (4 inches) and 51cm (20 inches). The rubber at the tip must be at least 6mm (1/4 inch) thick.
    1. The flexible tip must extend at least 10cm past the end of the haft.
    2. The spear-head must flex to 90 degrees with hand pressure and must substantially return to its shape within 3 seconds
  3. The rattan haft must have a diameter between 28.5mm (1 1/8th inch) and 35mm (1 3/8th inch):
    1. The haft must be inserted at least 5cm (2 inches) into the spear-head. The head must be friction-fitted to the haft according to the manufacturer's instructions.
    2. The head must be taped to the haft with strapping tape, fibreglass tape or duct tape. Contrasting coloured tape must be wrapped around the base of the head, so that the head's absence is readily apparent.
    3. The haft must have a flat end at the head of the spear with a diameter of at least 12mm (1/2 inch). The butt end of the haft may be rounded.
  4. You can put tape on the haft to help prolong its life. You can add augmentations or decorations, for example to stop a blade sliding along the haft or to make the haft easier to grip. You must make sure those augmentations do not weaken the haft or pose a safety risk. You cannot use augmentations that are designed to trap a blade
  5. The total length of the spear must be no longer than 275cm (9 feet).

Steel-headed spear

Note: Under the SCA Fencing Marshals' Handbook (April 2020) steel-headed spears will not be permitted for fencing combat after 31 December 2020, at the direction of the Society Marshal.

  1. Steel-headed spears must be made of a metal blade head mounted on a wooden or rattan haft.
    1. The metal head must be similar in design to the commercially available Alchem pike and Amazonia spear.
    2. The head must be at least 91.4cm (36 inches) long, as measured from the tip to the top of the tang. It must comply with the flexibility requirements for competitive swordfighting in Update reference - Appendix 4.
    3. The head must be secured to the haft by screws or pins.
  2. You can add augmentations to the haft (see rule 6.6.1.4)check reference
  3. The total length of the spear must be no longer than 244cm (8 feet).
  4. The maximum weight of the weapon must not be more than 1.36kg (3lbs).

Rubber-band guns

  1. Rubber-band guns must look like a period muzzle-loading weapon dated before 1600CE.
  2. Rubber-band guns must be made of sturdy, lightweight materials that will stand up to normal combat. You must make sure all edges and corners are smoothed off and that there are no splinters or cracks.
  3. Rubber band ammunition must be made from commercially available rubber tubing and must not contain any metal parts:
    1. Ammunition must not use any rigid materials beyond the minimum required to join the ends together. Any hard plastic on the outside of the band should be covered and smoothed by vinyl duct tape or plastic shrink wrapping.
    2. You are not allowed to fill the rubber bands with sand or liquids.
    3. You must mark each band to identify the owner.
    4. You can only use ammunition that has been inspected with the weapon you are using. You are not allowed to collect used ammunition during combat.
  4. There are two categories of rubber-band guns, classified by draw length -- the distance between the anchor point and the trigger that the ammunition hooks onto:
    1. Short-arm RBGs have a draw length not exceeding 45cm
    2. Long-arm RBGs have a draw length exceeding 45cm
  5. The circumference of the ammunition depends on the category of rubber-band gun.
    1. There is no restriction on the circumference of short-arm rubber-band gun ammunition
    2. The circumference of long-arm rubber-band gun ammunition must be at least the draw length of the rubber-band gun.
    3. For example, if an rubber-band gun has a draw length of 46cm, then the ammunition must have a circumference of at least 46cm.
    4. As a practical measure, a marshal can flatten a band in half, and use that to measure it against the draw length of the rubber-band gun.

Defensive objects

  1. There are two types of defensive object: rigid; and non-rigid.
  2. Rigid defensive objects must be made of sturdy materials that will stand up to the stresses of normal combat. You must make sure that all edges or corners are smoothed and that there are no cracks or splinters.
  3. Non-rigid objects may be made of cloth, leather and similar yielding materials. They may be weighted with soft material such as rope or rolled cloth. They may not be weighted with any rigid material, nor with materials that are heavy enough to turn the object into a flail or impact weapon.
  4. Defensive objects that contain both rigid and non-rigid components (such as a flag on a pole) must meet both sets of requirements. You cannot throw these objects (including, for example, a cloak with rigid clasps) at your opponent.
  5. You are not allowed to use an object that can bind an opponent's weapon to their body, or to their other weapon or defensive object - either deliberately or by accident. This might include ropes or whips. You can use a coiled rope or whip to deflect a weapon.

Non-standard defensive objects

  1. You can put a simulated spike or a similar offensive item on your buckler or shield. This is non-standard equipment and must be approved by the Fencing Marshal-in-Charge.
    1. Offensive items must only be made of cloth, foam, leather, glue and tape and must not contain rigid materials.
    2. On inspection, the offensive item must provide progressively resistant "give", without allowing contact with any underlying material.
  2. You must tell your opponent if you are using non-standard equipment. They can decide not to face it and ask you to use something else.